DO-160 electronics testing is on the critical path of airborne hardware programmes, as this is what proves that aircraft electronics will not fail during flight. The standard is published by RTCA as Environmental Conditions and Test Procedures for Airborne Equipment, and its European counterpart, EUROCAE ED-14, is described in RTCA special committee documentation as technically identical. It is widely referenced by regulators, aircraft and equipment manufacturers, customers and test laboratories, so a design team may be handed DO-160 early and expected to understand it fully.
This post is written for two readers. Engineers will find the section groupings, design considerations and revision questions that shape a test plan. Programme managers and buyers will find the factors that drive laboratory time, retest risk and supplier selection. It follows the overview, Aerospace Electronics Validation: An Engineer’s Guide to Certification, which placed DO-160 within the wider certification framework. Here the focus stays on the environmental standard.
What DO-160 covers (and what it leaves to other standards)
RTCA first published DO-160 in 1975, and the current published revision remains DO-160G, issued in 2010, according to RTCA’s DO-160 page. The FAA advisory circular that recognises it, AC 21-16G, describes the tests as a laboratory means of demonstrating equipment performance in environmental conditions. The circular is not mandatory and sets out one acceptable means of compliance among several possible ones. RTCA also publishes DO-160G Change 1, which accounts for information removed to create the separate DO-357 user guide.
In practice, the standard supplies test conditions and procedures. Performance criteria come from the equipment specification (a minimum operational performance standard or a Technical Standard Order). The applicant then selects the sections and categories that match the equipment’s intended installation and operating environment, including factors such as where and how it will be installed and what it does. A summary of those choices is recorded in an environmental qualification form that accompanies the test report.
|
🛠️ DESIGN CONSIDERATION Establish the intended installation environment before the mechanical and electrical architecture is frozen. Changing the assumed environment at a later stage could change the applicable test categories and the design margins required. |
The 26 sections of DO-160G (grouped by what they test)
Sections 1 to 3 cover purpose, definitions and general test conditions, and the individual tests run from section 4 to section 26, as the published section list shows. Grouping the tests by what they stress makes planning easier.
Climatic and fluid environment. Section 4 (temperature and altitude), section 5 (temperature variation), section 6 (humidity), section 10 (waterproofness), section 11 (fluid susceptibility), section 12 (sand and dust), section 13 (fungus resistance), section 14 (salt fog) and section 24 (icing) represent the conditions an installed unit meets from weather and altitude. Which of them apply depends on where the unit sits on the aircraft.
Mechanical loads. Section 7 (operational shocks and crash safety) and section 8 (vibration) apply mechanical stress. Both place demands on the mounting structure, the connectors and the internal assembly of the unit, and the next post in this series, Vibration and Shock in Aerospace Electronics, covers them in depth.
Electrical power and electromagnetic compatibility. Section 15 (magnetic effect), section 16 (power input), section 17 (voltage spike), section 18 (audio frequency conducted susceptibility), section 19 (induced signal susceptibility), section 20 (radio frequency susceptibility), section 21 (emission of radio frequency energy), and section 25 (electrostatic discharge) test how the unit behaves in the aircraft’s power and signal environment and what it radiates in return.
Lightning and hazardous conditions. Section 22 (lightning-induced transient susceptibility), section 23 (lightning direct effects), section 9 (explosive atmosphere) and section 26 (fire and flammability) address events with safety consequences. Section 26 needs particular attention because the advisory circular on DO-160 versions does not treat DO-160 Section 26 as a universal substitute for the applicable aircraft or engine fire and flammability requirements. FAA AC 21-16G states that DO-160G Section 26 is sufficient for 14 CFR Part 25 but not Part 33; engine applications require the applicable Part 33 guidance. Check the applicable circular and TSO before relying on it.
Where DO-160 electronics testing drives cost and schedule
Applicability for DO-160 electronics testing differs by product, yet some sections can shape effort consistently. Vibration testing exposes weaknesses in mounting and connector retention, and a failure may lead to mechanical redesign. Temperature and altitude testing set requirements for component selection and thermal design. The power input and lightning sections can force changes to input protection and filtering, while emissions and susceptibility testing can lead to layout and shielding revisions late in a programme.
|
⚠️ CRITICAL ALERT A failure late in formal testing can trigger design change, retest of affected sections and, frequently, a wait for the next available laboratory slot. For programme planning, consider carrying contingency for at least one retest of a high-risk section. Design changes made after qualification may also reopen test scope, so agree with the customer or certification contact how changes will be assessed for retest. |
Choosing the revision: DO-160G, DO-160H and your customer’s specification
AC 21-16G recognises revisions D, E, F and G as acceptable environmental qualifications for showing compliance with certain airworthiness requirements, and the FAA strongly encourages G for new articles. The applicable revision may be specified by the TSO, equipment specification, customer requirement or certification basis. Where the governing requirements do not specify a revision, the applicant may have some flexibility, but the choice should be agreed upon with the relevant certification authority before testing.
As of October 2026, DO-160H remains in development. RTCA’s 2025 year in review reported that its environmental testing committee, SC-135, had handled more than 2,000 review comments across all 26 sections and that publication was expected in autumn 2026. Current EUROCAE WG-14 material still lists ED-14H as Draft with a target publication date of 30 September 2026, while FAA AC 21-16G remains active. A December 2025 committee report records that the FAA plans to invoke Revision H through an updated advisory circular, AC 21-16H. Committee work has also highlighted Section 26 as an area requiring particular attention, which is more reason to confirm early how fire and flammability will be evidenced.
|
⚠️ CRITICAL ALERT At the time of writing, G remains the revision named in AC 21-16G. A programme starting now should state which revision it is testing to and agree what happens if Revision H is published part-way through. If your customer has not named a revision, make sure to ask. |
Planning a DO-160 electronics testing programme (from categories to test report)
A standard DO-160 electronics testing programme has four phases:
- Define the environment: Record the installation location, aircraft type, applicable categories, operating environment and equipment function, together with the performance criteria from the equipment specification, and agree to them with the customer or certification contact.
- Design and pre-compliance: Build margin into mounting, thermal design, filtering and protection, then test representative hardware in the highest-risk areas.
- Formal testing. Freeze the test article configuration, issue a test plan and procedures, and run the campaign at a laboratory, with witnessing where the customer or authority requires it.
- Reporting and change control: Produce the test report and qualification form that support the applicable certification or approval basis, and agree how later design changes will be assessed for retest.
|
🛠️ DESIGN CONSIDERATION Run pre-compliance testing on representative hardware in the sections most likely to expose design weaknesses. This may include vibration and EMC testing depending on the equipment and installation. Bear in mind that finding a resonance or an emissions problem on a development unit costs far less than finding it in a formal campaign. |
Case Study: The 2013 Ethiopian Airlines 787 Fire
On 12 July 2013, a parked Ethiopian Airlines Boeing 787-8 caught fire at London Heathrow. The UK’s Air Accidents Investigation Branch concluded that the fire began with an uncontrolled release of stored energy from the lithium-metal battery in the aircraft’s emergency locator transmitter. Trapped battery wires had compromised the environmental seal between the battery cover plate and the unit, giving flames and decomposition products an exit path, as the Aviation Safety Network summary of the AAIB findings records.
The investigation also found that the safety assessment supporting the transmitter’s certification had not identified battery failure modes as a hazard to the aircraft. Therefore, none had been mitigated in the unit design or the installation.
The report does not describe a DO-160 electronics testing failure, and this article does not suggest one. The case is useful because it marks a boundary. Environmental qualification shows how a unit performs under defined conditions in a laboratory. It does not replace the separate safety assessment, design assurance, installation controls and production controls needed to address hazards and failure modes, which the post on Aerospace Documentation and Design Assurance covers later in this series. A supplier who can explain both layers is easier to trust with a certification programme.
|
WORK WITH THE TEAM Ignitec’s engineers support airborne electronics programmes from early design through to qualification planning. If you are scoping DO-160 testing, we can review your chosen categories and identify design risks in vibration and EMC performance before you commit to a test plan. |
Contact the team to discuss your DO-160 electronics testing programme and qualification strategy.


